Finding a manufacturer takes two steps, and most buyers stop after the first. Step one is getting enough candidates in front of you. Step two is throwing out the ones that aren't manufacturers at all. Most of what follows applies whether you're ordering custom power banks or a small trial run of cables.
Step two is where deposits get lost, and it's the one nobody writes about. So this covers both — where to look, then how to check what you found.
Where Chinese manufacturers actually are
Six channels. Each gets you something different, and none of them tells you whether a supplier is real.
Huaqiangbei and the physical markets. The densest electronics cluster in Asia. One morning puts twenty products in your hand and a quote in your inbox before lunch. What it doesn't give you is a factory: most counters are a trading layer sitting on top of plants two hours away.
1688.com. The domestic wholesale platform. Prices are quoted in RMB to Chinese buyers, which makes it the fastest way to see what a product actually costs before export markup. It's in Chinese, payment is domestic, and nobody there is set up to answer an English technical question.
Alibaba and Made-in-China. The export layer. Everyone there says they're a factory, and everyone has a folder of certificates. Good for response speed and document comparison. Bad for telling a plant from a trader, because the platform doesn't ask.
Trade shows. Canton Fair in Guangzhou runs twice a year; the Hong Kong Electronics Fair runs spring and autumn editions. This is the one channel where you can ask an engineer a real question — how many SMT lines, do you run your own mould shop — and watch him answer.
Search and industry media. Slow, but it surfaces the plants that publish technical content. A supplier who writes about ageing racks and AQL sampling is usually a supplier who has them.
Referrals. Fastest and hardest to get. A buyer who already runs your product's category will tell you who to avoid, and that list is worth more than any directory.
Channels decide the quality of your shortlist. They don't decide whether a supplier is telling the truth. That's the next section.
How to tell a manufacturer from a trading company
Four questions, ordered by how little they cost you.
1. Business licence and plant address. Ask for the licence and check whether the registered scope includes manufacturing — not just "sales of electronic products". Then check the address. An industrial park in Bao'an or Longgang is a plant. An office floor in Futian is an office.
2. Production steps. How many SMT lines? Do you do your own injection moulding, or send it out? How big is the ageing room? A trader answers these with adjectives. A plant answers with numbers, because he walks past them.
3. The floor. Can I walk it now, on video, without a script? See Check 2.
4. Tooling. Do you have your own mould shop, or do you "find a friend" when a client needs a new housing? This one question separates most of the market.
A trading company isn't automatically a bad choice. For a small mixed-carton order, or when you need someone who answers email in English at 9am your time, a good trader earns his margin. Just don't pay factory pricing for it.
China supplier verification: five checks before the deposit
Run these in order. Each one is cheap, and each one kills a different failure mode.
Check 1 — The name on the certificate must be the name on the contract
Ask for the certificate number, not a photo of the certificate. Then look the number up on the issuing lab's site. Three things have to line up: the applicant, the product category, and the model number.
The common trick isn't a forged certificate. It's a real one attached to the wrong product — a report for a different device line, or a report issued to the supplier's upstream plant rather than the company you're paying. The PDF looks perfect, because it is. It just doesn't cover what you're buying.
A simple rule: if the applicant on the report isn't the entity printed on your proforma invoice, ask for one that is. A plant can have a report reissued under its own name. A trading company usually can't.
For power banks, these are the documents that matter:
- UN38.3 — transport. No airline takes the cells without it
- IEC 62133-2 — cell safety
- CE — EMC plus RoHS. A self-declaration and a technical file, not a certificate issued by a notified body
- FCC — the US EMC requirement
- UL 2056 — if you sell into US retail
Red flags: a scan with no number, an applicant name that differs from the company you're paying, a product description that doesn't name your product, or "our other model has it".
Most failures caught at this stage aren't design problems at all — they're document problems. Why custom power banks fail certification walks through the five that keep repeating.
Check 2 — A video call is not a factory tour
Anyone can film a clean room. Ask for a walk instead of a show: raw material area, SMT, assembly, ageing, packing. Ask them to keep the phone on while they move between stations. Ten unedited minutes tell you more than a polished three-minute clip.
What to look for on the walk:
- Ageing racks with units actually running
- A QC station with the sampling plan on the wall
- A sample retention cabinet — every serious plant keeps a unit from each batch
- Cartons labelled with a customer name, not only "export"
If flying out isn't realistic, a third-party inspection firm can walk it for you. Insist on the report number and check it on the firm's site. Photos without a report number are just photos.
Check 3 — Sample first, then a trial order sized to reality
Two to five units tell you whether the product works. They tell you nothing about whether the third batch will match the first.
The trial order is the real test, and its size depends on one thing: whether your product needs tooling. A private-label build on an existing mould can start small. A new housing needs a mould, and a mould carries its own minimum. Ask which case you're in before asking for a number — a quote that ignores this is a number you can't hold anyone to.
Two documents to ask for with the trial:
- A first article inspection report (FAI) — the first units measured against the drawing
- An AQL 2.5 inspection report — the sampling standard most US and EU buyers write into their PO
Check 4 — The quote that's 30% under everyone else
When ten suppliers cluster within 8% of each other and one lands far below, the gap is usually inside the product, not in the seller's generosity.
Four places it hides:
- Cell capacity — 10,000mAh printed, 6,000mAh measured
- Housing — aluminium look, ABS weight
- Cable — copper strand count and gauge
- Certification — the report covers the sample, not the batch
Weight is the cheapest check you can run yourself: a charging cable that feels 20% lighter than the sample you approved is telling you something the spec sheet won't.
Ask for the BOM. A real plant will tell you the cell brand, the measured capacity, the housing material, the wire gauge, and which certificate covers which part. A trader sends a price list.
Check 5 — Ask what they can change, not what they sell
Every supplier can print your logo. That's a sticker, not a capability.
Three questions separate a plant from a reseller:
- Can you change the housing structure — ribs, wall thickness, port layout?
- Can you change the PCBA — add a port, change the charging protocol, move the LED?
- What does a new mould cost, and how many weeks from drawing to first samples?
If the answer is "we can ask our factory", you're talking to a trader. Not fatal — just price it accordingly and hold them to the same five checks. Where tooling and PCBA changes sit on a timeline is mapped here: how OEM/ODM manufacturing works, stage by stage.
Red flags worth walking away from
- The certificate applicant is a different company
- No sample retention, no FAI, no inspection report
- Refuses a walk-through, offers only edited video
- A price far below the cluster with no BOM to explain it
- Can't name the cell supplier
- Answers every tooling question with "we'll see"
Frequently Asked Questions
1. How do I find a Chinese manufacturer for a product that doesn't exist yet?
Start from the closest existing product on 1688 to get a real cost floor, then approach plants that already run that category and ask what they can change. A plant with the right mould base will quote a modification; one without it will quote a brand-new programme.
2. Is Huaqiangbei a good place to source charging accessories?
For comparison, yes — you'll see more product in a morning than in a month of email. For production, no. The market is a trading layer. Use it to build a shortlist, then verify the plant behind each counter.
3. How do I check whether a CE certificate is genuine?
There's no EU-wide certificate database, because CE is a self-declaration. Start with what a CE certificate actually is, then ask for the test reports behind it — EMC and RoHS — plus the technical file, and check that the applicant and product on the report match what you're buying.
4. What's the minimum order for a custom power bank?
[待确认:existing-mould MOQ / new-mould MOQ] — the number depends on whether you need a new housing. Send your spec and we'll quote the case that applies.
5. Can you ship DDP and prepare FBA labels?
Yes. Door-to-door DDP and Amazon FBA labelling are both standard, and we send label artwork for approval before the cartons are printed. Submit your sourcing request and we'll come back with the freight options.
Why this plant, in four checkable facts
We run custom 3C accessories OEM & ODM services out of a plant in Shenzhen. Four things worth checking before you take our word for anything.
1. Fourteen years on the same product line. Shenzhen BHD Technology has been building charging accessories since 2013 — power banks, wall chargers, cables, wireless chargers, earbuds and speakers. This isn't a trading office that added chargers last year.
2. The files carry our own name. The CE, RoHS and FCC reports we hand over list Shenzhen BHD Technology Co., Ltd. as the applicant — the same name that appears on your invoice. Ask for the report numbers and look them up; that's what they're for.
3. Design and tooling are in-house. Industrial design, mechanical engineering and prototyping sit in our own office, and the moulds run on our own machines.
4. One person owns your order, start to finish. Engineering, QC, sales and after-sales are under this roof — 60+ people. The person who quoted you is the one chasing the floor, not a desk forwarding emails.
If you'd rather check before you talk numbers, start here: ask for the certificate numbers, book a walk-through, and order samples. That's the order we'd use ourselves.

